Now that the LED lighting transformation is now in full swing, there is another, less conspicuous revolution going on in the manufacturing of LED lamps – the more comprehensive testing of color values and brightness for improved lighting consistency.
The potential for output variations that seem to be inherent in LEDs can be problematic for lamp manufacturers, light fixture producers and customers who desire consistent color and brightness. This may be especially true of customers who have dramatic architectural lighting installed, with LED fixtures that can travel continuously down hallways, around corners, and up stairways.
This “consistency revolution” is particularly concerned with the more complete testing of the performance of light engines, the power source of LED lamps. Composed of the combination of one or more LED modules, together with an LED driver (also known as electronic control gear, or ECG), the variations in light engine output account for most of the variations in LED color temperature, brightness and other output characteristics.
If LED light engines are not subjected to more comprehensive and consistent testing, it is likely that those LED output characteristics will continue to vary as current LEDs are replaced by rapidly changing LED technologies.
The lighting industry has sold (or binned), LEDs by brightness (intensity) and color (CCT) for decades, so in that sense LED binning is really only an extension of an existing paradigm.
With literally 100s of separate color and intensity bins, it will be difficult for end users to get accurate replacement lamps, since it may be problematic to trace the binning number, or the chip used in the original lamp’s light engine may have been superseded with a model that produces somewhat different light characteristics.
Controlling Quality at the Source
To alleviate this problem many LED light engine manufacturers provide 100 percent “functional testing” of lamps along with first article and periodic inspections of a production run. However, functional testing merely validates that the lamps will illuminate, and usually don’t analyze the CCT (correlated light temperature), CRI (color rendering index) or brightness of lamps. If there were an improperly marked or binned reel of components it would be possible to produce a significant number of units that had improper performance characteristics.
The more complete solution would be the comprehensive testing of 100 percent of LED light engines, and those who manufacture those items are developing more sophisticated testing systems that will automatically and thoroughly test them before they are sold to lamp manufacturers.
Companies such as MADE (Manufacture And Design Electronics – formerly CI Lighting), a supplier of US manufactured LED light engines to the industry, are moving toward 100 percent comprehensive testing, control and data reporting and recording, plus production controls via a robotically-controlled test cell that will inspect and record the circuit boards for each light engine, including color temperature, power (voltage and or current readings), brightness (luminous flux), and color rendering index.
By testing and controlling those factors, light engine manufacturers will enable the production of LED lighting with much greater consistency in power, color and brightness attributes, saving time and binning efforts in the process. MADE, for example, now applies this type of testing to all types of customer LED light engine designs, including those for retrofit products such as the light strips that replace fluorescent lamps and ballasts.
“This inspection technology will provide our customers the assurance that the extensive binning processes we employ are producing the desired results in the final products they manufacture,” said Donald Bernier, MADE president. “We can be 100 percent sure that the binning is providing the desired three-step McAdam ellipse color results as well as provide voltage and current binning characteristics for the individual boards as well. This will allow our customers who use a constant current driver to match light output from one module to the next, thereby providing consisting color and intensity results.”
An added benefit of this new approach is that production will be stopped if product is out of tolerance, thereby reducing the risk of scrapping product. Reducing such waste will enhance cost competitiveness and provide competitive advantages, both price and reliability, even with offshore suppliers.
The Value of Consistency
Mike MacLeish, Director of Engineering at SPI Lighting, agrees that the consistency of LED color attributes and brightness have a definite influence on lighting quality and applicability. SPI Lighting, which uses LED light engines from MADE, produces a broad range of fixtures including architectural lighting for workspaces and building exteriors, high-power asymmetric commercial lighting, and linear lighting for spaces such as offices and retail stores.
“In our industry, and particularly with architectural lighting, you have lighting fixtures where you view the source directly,” said MacLeish. “So it is critical to make certain that the color temperatures and brightness of the lamps are consistent. I won’t release a design unless I’m sure those requirements will be met.”
Like other lighting manufacturers, when SPI creates lighting fixtures the lamps are graded by the color temperature that the light produces, which varies from “warm,” such as a candlelight color, up to “daylight,” which is equivalent to the bright light you see outside.
“This measure is called CCT, correlated color temperature, which is gauged in degrees Kelvin,” MacLeish said. “When it comes to LED lighting, we look at 2,700 Kelvin as “warm,” and 5,000 to 6,000 as a “true bright” or cool temperature. This is important to users because when they put lighting in their kitchens they don’t want it to look like the lighting in a doctor’s office; on the other hand, the doctor doesn’t want his office to have the look of candlelit fire.”
Another factor, the CRI (color rendering index) is also an important measure to lighting manufacturers that is inspected by the new light engine testing system. CRI is the ability of the light source to be able to portray the true color of the objects it’s illuminating in their true color form, which is how the color would look in natural sunlight. The latter is the temperature that would enable people being able to see the true color of paint chips or other color samples.
“CRI is measured from 0 to 100, and a good color rendering ranges from the upper 80s to mid-90s on the index,” MacLeish said. “Examples good uses for this higher range would be a grocery market where the owner wants the customers to see red apples as a healthy red, and the green apples to look the authentic green.”
Both color condition temperature (CCT) and the color rendering index (CRI) are very important to the lighting industry, he adds.
It is noteworthy that even today’s more robust binning systems can fall short of providing the consistency that is promised by the 100 percent light engine testing system. One reason is that the electroluminescence, the luminescence produced by voltage to an LED lamp, as well as color of the light is determined by the lamp’s light engine microchip. Since the chips used in LEDs continue to change over time, their manufacturers often recommend a “blending” technique to achieve the desired lamp color correctness and facilitate more accurate binning. However, this technique may not produce the consistent results that lighting manufacturers are looking for.
“When we go from production lot to production lot, we have concerns that blending – ‘recipe’ that chip manufacturers recommend to achieve a common color within the color temperature tend to vary from one generation of the LED product to the next,” said MacLeish. “With different chips we see shifts that can make them fall outside the visual parameters to a point where the differences becomes noticeable.”
The new 100 percent testing system can make adjustments during production runs in order to compensate for chip variations and achieve more uniform color and brightness characteristics.
Enabling Accurate Replacement
In addition, in conjunction with the 100 percent inspection process, this new test system stores all pertinent LED light engine lighting characteristics, from lot to lot, in a database that can be made accessible to lighting manufacturers.
This database could prove valuable to manufacturers for use in handling warranty claims and as an extended service to enable them to match the color and brightness of an LED lamp from a given production lot years later when the lamp eventually requires replacement.
“Having the ability to match an LED light with one produced years ago would be an important capability, MacLeish notes. “We might know exactly what model the chip is, and that same chip might not be available, so the chip manufacture will provide us the closest model, and that is usually within an acceptable range. To actually tune a chip down to a very close color mix of a lamp that requires replacement is really fantastic.”
For more information, contact MADE, 1124 Centre Road, Auburn Hills, MI 48326; Phone: (248) 850-390-1425; Email: firstname.lastname@example.org; or visit the web site: made-usa.net